Stamped Irrigation Components
We make springs and stamped irrigation components for equipment manufacturers, and our programs run from 100,000 parts to programs that exceed 3 million pieces per year. Perfection Spring & Stamping Corp. has produced stamped metal brackets, springs and clips since 1955, and custom stampings and springs for irrigation systems sit inside our agricultural work next for utility vehicles and large structural parts for planting equipment.
If you source metal irrigation brackets, mounting plates, clips, or springs for irrigation systems, this page covers what we run, what we make them from, and how a program moves from drawing to production. For the full range of lawn, garden and farm parts, start with our lawn and garden stampings and springs page.
Irrigation Brackets and Support Parts We Stamp
Irrigation hardware has to hold lines, fittings and housings in position outdoors for years. Our bracket work includes gussets for added bending strength, mounting and support features, and tube holders, all produced from coil in progressive dies and four-slide tooling. See our stamped metal brackets page for the general bracket range.
When a part needs a spring element, such as a tensioning or latching detail, we can supply the matching springs or wireforms from the same plant, so the stamped and wire-formed pieces of an assembly come from one supplier and one quality system.
Presses From 30 to 600 Tons
Our progressive die presses run from 30 tons to 600 tons. The 600-ton press, together with upgraded coiling equipment, is what lets us take on the larger components that irrigation and other agricultural equipment call for, rather than limiting a program to small brackets.
We design and build tooling internally to your geometry, and long runs depend on protecting it. In-die sensors for die protection matter when a single program is planned in the millions of pieces.
Materials and Finishes for Outdoor, Wet Duty
Irrigation parts spend their life in water, soil and sun, so material and finish decide service life more than geometry does. For outdoor use we recommend corrosion-resistant material, either stainless steel or a treated alloy, paired with a protective finish. We stamp stainless steel, steel, aluminum, copper and brass; see our stainless steel stamping page for grades.
Finish options we run include e-coating, black e-coat, yellow-zinc plating and electro-galvanizing. We confirm the material and finish pairing during quoting, before tooling is cut.
Engineering Input Before Tooling Is Released
Our engineers review forming feasibility, tolerance control, and tooling considerations at the start of a program, so the part that goes into the die is the part that can be held to tolerance at volume. Our engineering and design services cover that review.
If your current stamper is the constraint, we also handle tooling transfer, so a running part can move to us without redesigning it. Our case studies, all in other industries, document customer savings from $150,000 to $5.7 million on a single program, which shows how we approach cost on a part.
Quality System and Certifications
Buyers who qualify suppliers for long programs ask for documentation first. We hold IATF 16949:2016, ISO 9001:2015 and ISO 14001:2015 certification, and we support PPAP part approval. Where an assembly has cleanliness requirements, our part washing meets ISO 16232 technical cleanliness standards.
Request a Quote for Stamped Irrigation Components
Send a drawing or sample part with the material, finish and annual volume you expect, and we will review it for forming feasibility and quote it. If the part is for outdoor or wet use, include that so we can check the material and finish pairing before tooling is cut.
Need a custom solution?
If you are looking for cost reduction through design innovation, challenge us!
Frequently Asked Questions
A drawing or sample, the material and finish you want, and your expected annual volume. If the part will sit outdoors or in contact with water, say so, and we will check the material and finish pairing during quoting.
Yes. Tooling transfer is part of our capability, and our engineers review the existing tooling and part for forming feasibility and tolerance control before production moves.
Yes. We make compression, extension and torsion springs and CNC wireforms in the same facility, and we also offer mechanical assemblies, so a bracket and its spring can ship from one supplier.
Our progressive die presses range from 30 to 600 tons. The 600-ton press and upgraded coiling equipment handle our larger components.
Explore Other Industries We Serve
From automotive to construction, Medical to HVAC, and more
Perfection Spring & Stamping Corp. is a manufacturer of custom metal components, serving a wide variety of industries. Ranging from "Global Fortune 1000" companies to the individual with a patent on a single-part, we serve a diverse portfolio of customers, markets & industries around the globe.
